Recapturing Your Tiles Original Lustre
Grout restoration is a task that most first time bath renovators’ dread. The unsightly appearance of cracking grout or mortar that is full of dirt and mildew can cause any homeowner to stare in despair and disbelief. Luckily, depending on the problem you are facing with your bath there are a number of refurbishment recommendations that you can be used to make it sparkling new again.
In many instances these methods only require proper cleaning to capture the original appearance of your grout. In other instances you will have to use repair techniques by removing old mortar and replacing it with new grout and sealant once more. While most homeowners dread the thought of the work involved that requires replacing grout, in many cases it is the best solution for unsightly tiles. Below you will find a list of techniques that you can apply in your bath to make it beautiful and clean again.
Clean the Mortar
The first thing that should be done when you are considering grout restoration is cleaning your tile floors or walls. By cleaning the mortar lines with specially made solutions you will be able to evaluate the extent to which your grout can be repaired without resorting to removing it all together. You may use acid base cleaners, oxygen bleach or even hydrogen peroxide in cleaning grout.
These are very strong chemicals, so always remember to protect your hands by using gloves. Once you have applied these chemicals then allow a few hours to pass before you arrive at a conclusion about the result. You may try reapplying the chemical you used once again to see if the stain, mildew or dirt is lessened or removed.
Coloring the Compound
If you find that the grout is not cracked, but discolored then you may want to try coloring the mortar by first learning about these color grout fundamentals. Coloring the grout is an easy process that involves using colorant in areas where grout has been applied.
However, you will need to determine the type of grout that you have before you consider using this method. If you have unsanded grout then the best advice will be to remove it all together. However, if you find you have sanded grout then you can easily use a grout colorant as was mentioned earlier.
Try to select a colorant that will complement the original look of your bathroom or create a new personalized look that you are satisfied with. You can try using the colorant on a small area to see how it blends with the tiles and faucets that are already in the bathroom.
Another useful tip to bear in mind when considering staining techniques would be to use masking tape along the end of each tile. This will prevent you from discoloring the tile in the process and make it a lot easier to color along the line of the joints. Always ensure that the surfaces you are coloring is clean and also intact. Broken and old mortar should be removed and not colored.
Removing Old Sealant
If you find that cleaning and coloring are not helping then the next recommendation is to repair or to remove the grout all together. This can be a laborious task depending on the restoration area in question and the extent of damage on the joint lines and having the right tools in your tiling toolbox goes a long way in easing the process. The steps involved in this tile and grout restoration process are:
Remove thin seams of grout with a utility knife and wider seams using a grout saw. If you are using a saw for mortar removal, then you will need to wear a mask; because, this can be a very dusty process. You should ensure that you are digging out enough of the old mortar to guarantee firm footing for the new one, Superficial removal will not help, because this is just a temporary solution.
Once you have removed the old grout then the next step is to clean the area with a brush or with a vacuum. Check to ensure that all bits and pieces of mortar have been removed before you apply a new one.
Applying the Final Touches
Apply the new mortar using a rubber squeegee or grout float. You will also need cloth, water and a sponge to wipe away the excess during the grout restoration project. Remember to apply the correct type of mortar based on the tile, spacing and area in question. If you are re-grouting a thin seam then you will use unsanded grout. If, however, you are re-grouting a thicker seam then it will have to be sanded mortar. For porcelain and ceramic tiles, use sanded grout and for stone you may use unsanded grout
Allow the area to dry after the grout restoration process and apply a sealant that is compatible with the type of gout used.
Categories with solutions that teach you how to restore your bath to its original state. Brush up on your interior design techniques, Remodel your washroom. Comparable lavatory trending information and find restroom products compatible to your restoration needs and remove any doubts of finally getting the bathing space of your imagination. Here is some more information on tile trending ideas you can plan with.